Public Bellwether article

Shop Roaster: Installation Checklist (06/2026)

Source: Bellwether Coffee,https://help.bellwethercoffee.com/shop-roaster-installation-checklist. Reproduced for owners; © Bellwether Coffee Co.

Group: Install, power and safety

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co.

No Parts Required.

Tools Required:

  • Multimeter
  • Electric Screwdriver w/ Philips Bit and narrow extension
  • Boxcutter
  • Lifting gloves w/ grip
  • Metric Allen key/bit set
  • 1/4” ratchet
  • Philips #1 Screwdriver
  • Torque wrench

**

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Site Preparation**

  1. Confirm presence of a compatible outlet at roaster location, 1PH, 240V, 30A breaker.   (L6-30R in the USA, check local spec for international.)
  2. Confirm presence of a strong, usable WiFi network
  3. If setting up for Continuous Roast, four people able to lift must be present for install.

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Uncrating and Placement  >>> LINK <<<

  1. Move the crate as close to final location as possible before uncrating.
  2. Inspect boxes for damage. TAKE PICTURES OF ANY NOTABLE DAMAGE TO CRATE OR ROASTER.
  3. Prepare the roaster for lifting by setting up four handles along base of roaster.
  4. Have 4 people carefully lift roaster onto counter top for Countertop use.  If setting up Continuous Roasting, proceed to next section.

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Continuous Roasting Setup >>> LINK <<< Skip to next section if set up for Countertop use.

  1. Unbox Base Cabinet and Autoloader.  Cut plastic wrap around cardboard boxes, remove the lid and foam, pull side cardboard panel up to remove allowing easy access to components.
  2. Install wheel chock to keep the Base Cabinet from moving during install process
  3. Prepare Roaster for lift.  Install lifting handles, remove the Water/Chaff Can and insert.
  4. Prepare Base Cabinet for the lift.  Confirm that all exposed wires are pushed down into the Base Cabinet. Confirm that the water collection pipe is connected to the Boot and Water Collector nozzle on the Base Cabinet.
  5. With 4 people, carefully lift Shop Roaster onto Base Cabinet.
  6. Connect two sensors (Chaff, Bean Collector) at the rear of the Roaster.
  7. Attach (4) screws that connect Base Cabinet to Roaster.
  8. Remove the Cooling Tray and metal plate, replace with the Autobucket and then join barrel connector.  Insert metal Chaff Tube inside the silicone Chaff Boot, connect Boot to lipped groove on Chaff Connector.  Install the Valence.
  9. Remove side panels from Autoloader and lift on to the top of the Roaster.
  10. Remove shipping shims and screws in Autoload cabinet.
  11. Connect wire in Autoload to barrel connector inside of Autoload cabinet
  12. Replace lifting rods inside roaster, replace all panels

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Power On, Register Roaster, & Update Software >>> LINK <<<

  1. Attach power cable to rear of Roaster, plug into tested outlet.
  2. Flip Power Switch on the rear of Shop Roaster up to turn the power on.
  3. As the Roaster boots up, it will make some noises and the screen may flash a few times.  This is normal behavior.
  4. Once Roaster fully boots, confirm Hopper empty/full status and then click “Register Roaster” at bottom of screen
  5. Connect to WiFi network, wait for the Roaster to test speed and confirm connectivity.  If this times out, cancel (if available) or reboot.
  6. Once connected to the WiFi, a Software Update might automatically begin downloading.  The roaster may reboot on its own, this is normal behavior.
  7. Register to your account using the displayed QR code or URL.  Make sure to use the QR or URL before clicking continue or you will lose access and have to restart.

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Auto Loader Scale Calibration >>> LINK <<< Skip to next section if set up for Countertop use.

  1. Review the guide.  Confirm shipping shims were correctly removed and all other pre-calibration checks in the guide prior to calibration.
  2. Enter the Tech Panel (PIN 4377) and follow the instructions in the Hopper & Autoloader section for calibration.  Make sure to wait 5 second after taring/adding/removing weight or making a selection on the screen at each step.
  3. From the Tech Panel, confirm that weight is displayed as 5lb. and then shows “–” when the weight is removed.

**

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Testing>>> LINK <<<**

  1. Run through the Tech Panel Diagnostic Tests.
  2. Run through a Test Roast

**

Source: Bellwether Coffee, original article. Reproduced for owners; © Bellwether Coffee Co. Review Routine Maintenance Items & Train Operators**

  1. Proper use of the Autoloader (If Continuous Setup): >>> LINK <<<
  2. Daily Maintenance >>> LINK <<<
  3. Weekly Maintenance: >>> LINK <<<